Перейти к содержанию
Авторизация  
0xygen

Считывания кодов ошибок без Tech2

Рекомендуемые сообщения

0xygen

Here's a nice (and cheap) one: read out faultcodes yourself! No need to go to the stealers... Even most dealers don't know this!

- Take a seat in your car...

- Press the brakepedal and the accelerator-pedal fully at the same time

- Turn the ignitionkey till the lights in your dash come on but don't start the car!

In the display where normally your mileage is shown, you'll see "ECN" (error code number) and below it the faultcodes that have been stored. They appear one after another. At the end, your mileage will be shown again.

The first 4 digits indicate the fault, the last 2 digits contain a value.

For example: ECN 161450: problem with communication between immobiliser and key-transponder.

If no codes are shown, nothing has been stored!

ошибки:

B0132 battery voltage high C-123

B0132 low battery voltage C-123

B0158 outside temperature sensor voltage is too small DIS (Information Display) C-015

B0158 outside temperature sensor circuit voltage to open or big DIS (Information Display) C-015

B0283 rear window heater malfunction heating, ventilation and air conditioning B-015

B1000 replace the control unit - EEPROM errors C-002

B1000 replace the control unit - hardware errors C-002

B1000 replace the control unit - hardware errors C-002

B1000 control device to replace C-002

B1000 control device malfunction C-002

B1001 airbag control unit is not locked hardware and software B-003

B1001 vehicle identification number is not programmed hardware and software B-005

B1001 error programming hardware and software B-003

B1001 Linkslenker-/Rechtslenker- configuration errors C-002

B1001 control device is not calibrated hardware and software B-003

B1001 control device is not programmed hardware and software B-003

B1001 control device is not programmed hardware and software B-003

B1001 control device programming hardware and software B-003

B1001 variants code is not programmed hardware and software B-004

B1001 variant configuration is not programmed hardware and software B-003

B1006 control device to replace C-002

B1009 control device programming hardware and software B-003

B1016 vehicle identification number is not programmed hardware and software B-005

B1019 control device in the extradition state C-002

B1325 system voltage power too large B-003

B1325 system voltage power too small B-003

B1375 Geschaltete system voltage (A ignition) is not plausible with CAN signal B-005

B1385 terminal 15A dysfunction B-004

B1390 comfort closure circuit voltage power too small windows C-009

B1395 engine runs too small signal voltage EHPS (electro-hydraulic auxiliary power steering) C-003

B1420 power supply voltage is too large C-124

B1420 power supply voltage too small C-124

B1421 supply voltage signal is not in the target area C-124

B1428 relay starters dysfunction C-127

B1441 Geschaltete system voltage (Ignition A) Power too big C-125

B1441 Geschaltete system voltage (ignition ON) voltage too small C-125

B1451-voltage relay equipment too large or open circuit C-106

B1451 accessories relay circuit voltage is too large C-106

B1453 Geschaltete system voltage (Ignition A) Power too big C-125

B1453 Geschaltete system voltage (ignition ON) voltage too small C-125

B2961 position ignition key switch circuit malfunction C-002

B3601 holding magnetic key relay circuit malfunction AF 17-4 Automatic 4-speed gearbox C-005

B3644 switch channel high wheel remote stuck RQ (Entertainment Head Unit) C-012

B3644 switch channel high wheel remote control circuit resistance not in the target area RQ (Entertainment Head Unit) C-012

B3645 channel down button remote control wheel stuck RQ (Entertainment Head Unit) C-012

B3645 switch channel down steering wheel remote control circuit resistance not in the target area RQ (Entertainment Head Unit) C-012

Scrolling right B3646 wheel stuck RQ (Entertainment Head Unit) C-012

Scrolling right B3646 wheel circuit open RQ (Entertainment Head Unit) C-012

Scrolling right B3646 wheel circuit resistance not in the target area RQ (Entertainment Head Unit) C-012

B3647 switch voice remote control wheel stuck RQ (Entertainment Head Unit) C-012

B3647 switch Voice Control wheel remote resistance not in the target area RQ (Entertainment Head Unit) C-012

B3648 switch telephone wheel remote stuck RQ (Entertainment Head Unit) C-012

B3648 switch telephone wheel remote resistance not in the target area RQ (Entertainment Head Unit) C-012

B3649 Scrolling left wheel stuck RQ (Entertainment Head Unit) C-012

B3649 wheel Scrolling left open circuit RQ (Entertainment Head Unit) C-012

B3649 Scrolling left wheel circuit resistance not in the target area RQ (Entertainment Head Unit) C-012

C0252 control device in the extradition condition or defect hardware and software B-003

Wrong C0550 configuration variations programmed control unit or defective hardware and software B-003

C0550 control device to replace C-002

C0550 control device is not programmed hardware and software B-003

C0551 vehicle identification number is not programmed hardware and software B-005

Wrong C0551 variant configuration programmed hardware and software B-004

C0551 control device programming hardware and software B-003

C0551 variants code is not programmed hardware and software B-004

C0551 variant configuration is not programmed hardware and software B-004

False C0569 system hardware configuration and software B-003

C0800 system voltage power too large B-003

C0800 system voltage power too small B-003

C0920 control device is not programmed hardware and software B-003

C1523 system voltage power too large C-105

C1523 system voltage power too small C-105

C1550 control device to replace C-002

P0070 sensor ambient air temperature dysfunction B-024

P0100 air mass / volume knife dysfunction C-007

P0100 air mass / volume knife signal too large C-007

P0100 air mass quantities too small knife signal C-007

P0100 air mass meter error

P0105 intake manifold pressure sensor voltage error

P0110 intake sensor signal is too large C-008

P0110 intake sensor signal to small C-008

P0110 Ansauglufttemperaturfьhler error

P0110 CAN bus, no communication with ECM (engine control unit) Fahrzeugbezogene Prьfanleitung B-019

P0115 CAN bus, no communication with ECM (engine control unit) Fahrzeugbezogene Prьfanleitung B-019

P0115 coolant temperature sensor errors

P0115 engine coolant temperature sensor is not in the target area cooled engine C-002

P0115 engine coolant temperature signal is too large cooling engine C-002

P0115 engine coolant temperature signal is too small engine cooling C-002

P0120 throttle valves / pedal position donor "A" is not a target area C-005

P0120 throttle valves / pedal position donor "A" signal is too large C-005

P0120 throttle valves / pedal position donor "A" signal to small C-005

No P0130 plausibility between O2 sensor 1 Bank 1 and O2 sensor 2 bank 1 B-020

P0130 lambda probe dysfunction (Bank 1 Sensor 1) B-020

P0130 lambda sensor circuit not in the target area (Bank 1 Sensor 1) B-025

P0130 O2 sensor circuit voltage high (Bank 1 Sensor 1) C-019

P0130 O2 sensor circuit voltage low (Bank 1 Sensor 1) C-019

P0135 lambda probe heating dysfunction (Bank 1 Sensor 1) B-012

P0135 lambda probe heating open (Bank 1 Sensor 1) B-028

P0135 lambda probe heating voltage is too big (Bank 1 Sensor 1) B-012

P0135 lambda probe heating voltage is too small (Bank 1 Sensor 1) B-012

No P0136 plausibility between O2 sensor 1 Bank 1 and O2 sensor 2 bank 1 B-027

P0136 lambda probe dysfunction (Bank 1 Sensor 2) B-027

P0136 lambda sensor circuit not in the target area (Bank 1 Sensor 2) B-026

P0136 O2 sensor circuit voltage high (Bank 1 Sensor 2) C-023

P0136 O2 sensor circuit voltage low (Bank 1 Sensor 2) C-023

P0141 lambda probe heating dysfunction (Bank 1 Sensor 2) B-013

P0141 lambda probe heating open (Bank 1 Sensor 2) B-029

P0141 lambda probe heating voltage is too big (Bank 1 Sensor 2) B-013

P0141 lambda probe heating voltage is too small (Bank 1 Sensor 2) B-013

P0170 fuel correction dysfunction (Bank 1) B-016

P0180 fuel temperature sensor short-circuit/interruption

P0190 Mechanical fault in the fuel system failure

P0195 Цltemperaturfьhler error (at Y17DT and Y17DTL not VERBAUT!)

P0201 cylinder 1 injector signal too large B-011

P0201 cylinder 1 injector signal to small B-011

P0201 cylinder 1 injector circuit open B-011

P0202 cylinder 2 injector signal too large B-011

P0202 cylinder 2 injector signal to small B-011

P0202 cylinder 2 injector circuit open B-011

P0203 cylinder 3 injector signal too large B-011

P0203 cylinder 3 injector signal to small B-011

P0203 cylinder 3 injector circuit open B-011

P0204 cylinder 4 injector signal too large B-011

P0204 cylinder 4 injector signal to small B-011

P0204 cylinder 4 injector circuit open B-011

P0216 Einspritzbeginn error

P0219 engine speed is too large C-025

P0220 throttle valves / pedal position donor "B" is not in the target area C-005

P0220 throttle valves / pedal position donor "B" signal is too large C-005

P0220 throttle valves / pedal position donor "B" signal to small C-005

P0230 fuel pump primary circuit signal is too large B-010

P0230 fuel pump primary circuit signal to small B-010

P0235 boost pressure signal to donors large C-031

P0235 boost pressure donor signal too small C-031

P0243 boost pressure valve voltage too large C-032

P0243 boost pressure valve voltage is too low C-032

P0243 boost pressure valve open circuit C-032

P0251 overflow valve / pump control unit dysfunction (99% pump control unit died)

Several P0300 cylinder misfire detected B-021

P0301 cylinder misfire detected 1 B-021

P0302 cylinder misfire detected 2 B-021

P0303 cylinder 3 misfire detected B-021

P0304 cylinder misfire detected 4 B-021

P0313 misfire at low fuel levels detected B-021

P0325 Klopfsensor 1 signal too big (bank or individual sensor 1) B-022

P0325 Klopfsensor 1 signal too small (bank or individual sensor 1) B-022

P0335 crankshaft sensor wrong signal C-002

P0335 crankshaft sensor no signal

P0335 crankshaft sensor signal is not in the target area C-002

P0340 engine speed error '

P0340 camshaft position donor dysfunction C-009

P0340 camshaft position encoder signal to big C-009

P0340 camshaft position encoder signal to small C-009

P0340 camshaft position encoder circuit open C-009

P0340 camshaft sensor signal is not in the target area C-009

P0370 pumps position signal void

P0380 Vorglьhanlage short-circuit/interruption

P0381 Glьhzeitkontrolleuchte short-circuit/interruption

P0400 EGR valve errors

P0420 catalyst efficiency under limit (Bank 1) B-017

P0441 tank vent system wrong tank vent River B-014

P0443 fuel tank vent valve open District B-014

P0443 fuel tank vent valve voltage high B-014

P0443 fuel tank vent valve voltage low B-014

P0460 fuel level sensor signal is not in the target area IPC (instrument) B-012

P0480 cooler fan (small) short-circuit/interruption

P0481 cooler fan (big) short-circuit/interruption

P0500 vehicle speed signal is not in setpoint range B-023

P0500 distance frequency (employer) error (comes from ABS unit)

P0501 vehicle speed signal is not in setpoint range B-023

P0505 CAN bus, no communication with ECM (engine control unit) Fahrzeugbezogene Prьfanleitung B-019

P0505 idling regulator short-circuit/interruption

P0520 engine oil pressure switch / sensor is not in the target area IPC (instrument) C-018

P0530 air conditioners misprint

P0530 air conditioners pressure sensor signal is too large heating, ventilation and air conditioning C-009

P0530 air conditioners pressure sensor signal is too small heating, ventilation and air conditioning C-009

P0560 battery voltage error (over or under voltage)

P0560 system voltage dysfunction C-110

P0560 system voltage outside Area C-110

P0560 system voltage power too large C-109

P0560 power system voltage too small C-109

P0560 system voltage too high C-110

P0560 system voltage is too low C-110

P0560 supply voltage too high C-110

P0571 Bremslichtschalter short-circuit/interruption

P0571 switches brake malfunction exterior lighting / flasher Appendix B-014

P0601 control device to replace C-002

P0602 vehicle identification number is not programmed hardware and software B-005

P0602 injector volume adjustment is not programmed hardware and software B-015

P0602 tires extent not programmed hardware and software B-003

P0602 Security code is not programmed hardware and software B-003

P0602 Control Unit C-002 program

P0602 control device programming hardware and software B-003

P0602 ECUs programming errors (lack of out-of-code programming or index)

P0602 variant configuration is not programmed hardware and software B-004

P0603 ECU EEPROM errors C-002

P0603 control device to replace C-002

P0604 controller error - RAM C-002

P0605 EPROM errors C-002

P0605 control device to replace C-002

P0606 controller replace error (Worst Case - Total damage control unit)

P0606 control device malfunction C-002

P0606 controller re-initialization C-004

P0606 system voltage too high C-110

P0607 Klopfsensor circuit malfunction B-022

P0607 Klopfsignal module; control device to replace B-022

P0607 controller replace error (see above)

P0610 control device programming hardware and software B-003

P0615 starter relay circuit open C-127

P0615 Amplifier starter relay temperature too large C-127

P0615 starters voltage relay too large C-127

P0615 relay starters voltage too small C-127

P0621 generator control lamp arrangement dysfunction IPC (instrument) C-021

P0650 CAN bus no communication with CIM (Steering Column module) C-003

P0650 error display control light (MI) dysfunction IPC (instrument) B-008

P0703 Bremslichtschalter error

P0704 clutch switch error

P0704 clutch switch dysfunction CRC (electronic speed control) B-010

P0725 CAN bus, no communication with ECM (engine control unit) Fahrzeugbezogene Prьfanleitung B-019

P0725 engine speed error '

P0815 switches High Turn the steering wheel remote stuck C-002

P0815 switches high wheel remote switching circuit resistance not in the target area C-002

P0816 switches Runterschalten wheel remote stuck C-002

P0816 switches Runterschalten wheel remote control circuit resistance not in the target area C-002

P1100 Critical System Error Error

P1105 Barometrischer pressure sensor short-circuit/interruption

P1105 pressure sensor signal Barometrischer too large C-030

P1105 pressure sensor signal Barometrischer too small C-030

P1106 boost pressure donor signal is not in the target area C-031

P1110 vacuum tube switching valve errors

P1120 CAN bus, no communication with ECM (engine control unit) Fahrzeugbezogene Prьfanleitung B-019

P1120 pedal sensor 1 short-circuit/interruption

P1120 pedal sensor 1 signal to high C-004

P1120 pedal sensor 1 signal too low C-004

P1120 pedal position sensor 1 and 2 false signal ratio C-004

P1122 pedal sensor 2 short-circuit/interruption

P1122 pedal sensor 2 signal to high C-004

P1122 pedal sensor signal is too low 2 C-004

P1125 boost pressure solenoid valve errors

P1173 Einspritzmengenbegrenzung because Oeltemperatur error

P1180 fuel temperature sensor errors

P1195 Цldruckschalter short-circuit/interruption

P1220 Einspritzdauer monitoring error

P1230 main relay dysfunction power supply and communication C-013

P1243 turbocharger bypass solenoid valve voltage too large C-033

P1243 turbocharger bypass solenoid valve voltage too small C-033

P1243 turbocharger bypass solenoid valve open circuit C-033

P1243 turbocharger bypass valve not in the target area C-033

P1335 engine speed signal error

P1345 cam shaft speed error

P1481 fan control circuit open 1 engine cooling B-004

1 fan P1481 control circuit voltage engine cooling too large B-004

1 fan P1481 control circuit voltage too small engine cooling B-004

P1482 fan control circuit open 2 engine cooling B-004

P1482 fan control circuit voltage 2 too big engine cooling B-004

P1482 fan control circuit voltage 2 too small engine cooling B-004

P1483 fan control circuit open 3 engine cooling B-004

3 fan P1483 control circuit voltage engine cooling too large B-004

3 fan P1483 control circuit voltage too small engine cooling B-004

P1490 additional coolant pump circuit open B-015

P1490 additional coolant pump circuit voltage is too large B-015

P1490 additional coolant pump circuit voltage too small B-015

P1500 electronic throttle author dysfunction C-006

P1501 immobiliser coding errors

P1502 immobiliser error

P1503 immobiliser signal error

P1515 donor pedal position error

P1523 throttle author is not in the target area C-006

P1526 throttle author lower position not learned C-006

P1530 high voltage relay climate heating, ventilation and air conditioning B-016

P1530 low voltage relay climate heating, ventilation and air conditioning B-016

P1530 air conditioning requirement error

P1530 air conditioning relay circuit open heating, ventilation and air conditioning B-016

P1540 Climate pressure signal short-circuit/interruption

P1560 battery voltage error

P1560 Geschaltete system voltage (Ignition A) signal dysfunction (CAN) C-109

P1565 interface speed control dysfunction CRC (electronic speed control) B-006

P1600 engine torque is not plausible B-030

P1600 control device to replace C-002

P1600 controller error

P1601 temperature controller error

P1602 Maximum speed is not programmed hardware and software B-003

P1602 programmers / Replace control unit (SG) hardware and software B-003

P1602 control device programming hardware and software B-003

P1602 variant configuration is not programmed hardware and software B-003

P1603 control device to replace C-002

P1604 programmers / Replace control device

P1604 control device to replace C-004

P1606 engine torque is not plausible B-030

P1606 control device to replace C-002

P1610 immobilizer anti-theft function is not programmed B-009

P1610 immobiliser dysfunction Immobilizer B-009

P1610 immobilizer function programming error

P1611 Wrong security code error

P1611 Wrong security code immobiliser B-015

P1612 immobiliser signal error

P1613 immobiliser no signal or wrong signal Immobilizer B-008

P1613 immobiliser signal error

P1614 Wrong transponder key error (the chip is still in the key?)

P1614 Wrong transponder immobiliser key B-006

P1614 immobilizer anti-theft wrong signal B-008

P1615 ECM (engine control unit) Identification failed Immobilizer B-006

P1616 CIM (Steering Column module) wrong environment indicator Immobilizer B-006

Replace P1620 controller error

P1625 relay power supply fault

P1630 Kraftstoffeinspritzmenge error

P1631 controller error injection pump

P1635 Vorglьhanlage error

P1650 CAN error

P1651 CAN error

P1660 fuel Abschaltventil error

P1680 coolant temperature output short-circuit/interruption

P1690 control lamp voltage error

P1694 control lamp voltage error Glьhzeit

P1811 engine torque signal malfunction ABS / TC / ESP (vehicle dynamics system) C-011

P1814 Invalid signal of ECC (Electronic air conditioning) ECC / SAC (Electronic climate control) B-028

P1895 CAN bus, no communication with ECM (engine control unit) Fahrzeugbezogene Prьfanleitung B-019

P1896 CAN bus, no communication with ECM (engine control unit) Fahrzeugbezogene Prьfanleitung B-019

P2638 control device to replace C-002

U0001 CAN bus maximum configuration list is not programmed hardware and software B-003

U0009 CAN bus communication nodes no C-005

U0101 CAN bus, no communication with gearbox control unit C-003

U0121 CAN bus no communication with ABS / TC C-003

U0140 CAN bus no communication with CIM (Steering Column module) C-003

U2100 CAN bus dysfunction C-005

U2100 CAN bus communication dysfunction C-005

U2100 CAN bus communication errors C-005

U2100 No communication with CAN-bus (High Speed) C-005

U2100 No communication with CAN-bus (Low Speed) C-005

U2100 No communication with CAN-bus (Mid Speed) C-005

U2101 CAN bus (High Speed) maximum configuration list is not programmed hardware and software B-003

U2101 CAN bus (Low Speed) maximum configuration list is not programmed hardware and software B-003

U2101 CAN bus (Mid Speed) maximum configuration list is not programmed hardware and software B-003

U2101 CAN bus maximum configuration list is not programmed hardware and software B-003

U2102 CAN bus (Mid Speed) maximum configuration list is not complete hardware and software B-003

U2103 CAN bus communication nodes no C-005

U2103 CAN bus Rьcksetzzдhler overflow C-005

U2103 CAN-bus circuit malfunction C-005

U2103 No communication with CAN-bus (High Speed) C-005

U2103 No communication with CAN-bus (Low Speed) C-005

U2104 CAN bus (High Speed) Rьcksetzzдhler overflow C-005

U2104 CAN bus (Mid Speed) Rьcksetzzдhler overflow C-005

U2104 CAN bus Rьcksetzzдhler overflow C-005

U2104 CAN bus Rьcksetzzдhler overflow C-005

U2105 CAN bus, no communication with the engine control unit Fahrzeugbezogene Prьfanleitung B-019

U2105 CAN bus, no communication with ECM (engine control unit) Fahrzeugbezogene Prьfanleitung B-019

U2106 CAN bus, no communication with gearbox control unit C-003

U2106 CAN bus, no communication with TCM (automatic transmission control unit) C-003

U2107 CAN bus no communication with CIM (Steering Column module) C-003

U2107 CAN bus no communication with IPC (instrument) C-003

U2108 CAN bus, no communication with ABS (anti-) C-003

U2108 CAN bus no communication with ABS / TC C-003

U2108 programmers / Replace control unit (SG) hardware and software B-003

U2110 CAN bus no communication with ABS / ESP C-003

U2111 CAN bus no communication with EPS (Electronic Power Steering) C-003

U2112 CAN bus, no communication with CDC "> CDC"> SADS (Part Active damping system) C-003

U2112 CAN bus No communication with CDC (electronic damper control) C-003

U2113 CAN bus not communicate with SDM (airbag) C-003

U2113 CAN bus not communicate with SDM (Sensing and Diagnostic Module, airbag) C-003

U2116 CAN bus no communication with IPC (instrument) C-003

U2116 CAN bus no communication with IPC (instrument) C-003

U2117 CAN bus, no communication with DIS (advertisement) C-126

U2117 CAN bus, no communication with Info-Display C-126

U2120 CAN bus, no communication with AHL (headlamp control) C-003

U2127 CAN bus, no communication with ECC (Electronic Climate) C-003

U2139 CAN bus no communication with CIM (Steering Column module) C-003

U2140 CAN bus no communication with CIM (Steering Column module) C-003

U2140 CAN bus, no communication with UEC (engine room electronics central module) C-003

U2141 CAN bus, no communication with REC (Rear electronics central module) C-003

U2143 CAN bus, no communication with SAS (steering wheel angle sensor) C-003

U2144 CAN bus, no communication with ACC (adaptive cruise control) C-003

U2145 CAN bus, no communication with PAS (Park Pilot) C-003

U2146 CAN bus, no communication with SLM (driving stage / Fahrprogrammwдhlhebel) C-003

U2147 CAN bus, no communication with AHS (Zuheizer) C-003

U2149 CAN bus, no communication with TPMS (tire pressure monitoring system) C-003

U2173 CAN bus, no communication with PEPS (Open & Start) C-003

U2174 CAN bus, no communication with AHS (Zuheizer) C-003

U2174 CAN bus, no communication with EHS (heating) C-003

U2181 CAN bus, no communication with elektrohydraulischem hardtop C-003

U2201 CAN bus, no communication with RQ (Entertainment Head Unit) C-003

U2202 CAN bus, no communication with CDC (CD changer) C-003

U2206 CAN bus, no communication with DIS (advertisement) C-003

U2207 CAN bus, no communication with UHP (Univ. handsfree) C-003

U2208 CAN bus, no communication with ECC (Electronic Climate) C-003

U2213 CAN bus, no communication with DAB (Digital Audio Broadcast) C-003

U2215 control device to replace C-002

  • Upvote 1

Поделиться сообщением


Ссылка на сообщение
Поделиться на другие сайты

Для публикации сообщений создайте учётную запись или авторизуйтесь

Вы должны быть пользователем, чтобы оставить комментарий

Создать учетную запись

Зарегистрируйте новую учётную запись в нашем сообществе. Это очень просто!

Регистрация нового пользователя

Войти

Уже есть аккаунт? Войти в систему.

Войти
Авторизация  

×
×
  • Создать...