x-maks

FAQ: Сила затяжки болтов Z16LE* двигетелей

1 сообщение в этой теме

Моменты затяжки на серии двигателей Z16LE* и очередность затяжки болтов

Z16LET

Z16LER

Z16LEL

A16LET

A16LER

A16LEL

Engine Bottom End

  • Connecting Rod Bearing Cap - 25Nm + 30 degrees + 15 degrees (use new bolts, install pistons in order 2, 3, 1 and 4 rotate engine each time to ensure they are not seized)
  • Crank Shaft Bearing Cap - 50Nm + 45 degress + 15 degrees (use new bolts start in centre and spiral out)
  • Oil Pump - 20Nm
  • Oil Level Sensor - 8Nm
  • Oil Baffle - 8Nm
  • Oil Pan to Cylinder Block - 10Nm
  • Oil Pan to Tranmission - 40Nm
  • Crank Shaft Sensor Pickup 5Nm
  • Knock Sensor - 20Nm

Engine Mounts

  • Left Engine Mount - 80Nm + 45 degrees
  • Rear Engine Mount - 80Nm + 45 degrees
  • Engine Hoist Points - 25Nm

Engine Timing Gear

  • Cambelt Tensioner - 20Nm
  • Cambelt Guides - 25Nm
  • Cambelt Cover - 6Nm
  • Torsion Vibration Balancer - 95Nm + 30 degrees + 15 degrees (use new bolts)
  • Auxillary Belt Tensioner - 50Nm

Engine Top End

  • Cylinder Head Bolts - 25Nm + 90 degrees + 90 degrees + 90 degrees + 45 degrees (Use new bolts see order below)
  • Cam Shaft Bearing Cap - 8Nm (note bearing caps are numbered with numbers on head - observe tightening order)
  • Cam Shaft Pully - 50Nm + 60 degrees + 15 degrees
  • Cam Shaft Sensor - 6Nm
  • Fuel Rail to Inlet Manifold - 8Nm
  • Coolant Pipe to Cylinder Head - 8Nm
  • Rocker Cover to Cylinder Head - 8Nm
  • Inlet Manifold to Cylinder Head - 20Nm
  • ECU 8Nm

Engine Turbocharger & Exhaust

  • Turbocharger to Cylinder Head - 8Nm (Use new bolts, torque again after 5 minutes and observe tightening order)
  • Turbocharger Heat Shield - 8Nm
  • Turbocharger Oil Return - 8Nm
  • Turbocharger Oil Feed - 30Nm
  • Turbocharger Water Feed - 35Nm
  • Lambda Sensor 40Nm
  • Downpipe to Main Cat - 20Nm

Transmission, Clutch and Flywheel

  • Fly Wheel to Crank Shaft - 35Nm + 30 degrees + 15 degrees (use new bolts)
  • Gearbox to Cylinder Block - Stage 1 10Nm, Stage 2 60Nm (complete all bolts to stage 1 then all bolts to stage 2)

Очередность затяжки болтов

Cylinder Head

10 6 2 3 7

9 5 1 4 8

Rocker Cover

10 6 2 3 7

9 5 1 4 8

Turbo Charger

5 3 1 7

8 6 2 4 9

Cam Shaft

3 1 2 4

4

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах
Гость
Эта тема закрыта для публикации сообщений.